Laying parquet

The non-solvent-based penetrating polymer emulsion wax "Bestcire" provides a finishing patina maintained by frequent passages, while promoting easy maintenance, comparable to terracotta and tiling

A 5 ​​mm thick tinted mineral sole is poured, smoothed, sanded, waxed and polished on an existing floor, in order to give it hardness, resistance and elegance

The "Quartzcoulis" mineral grout is mixed as defined below, in order to obtain a smooth grout, which is then prepared or projected onto all existing horizontal and vertical supports, previously prepared and degreased, it is then poured, smoothed, sanded , waxed and polished to a thickness of 5 mm

In addition to its nuanced, patinated, moiré and saponified colored appearance, the extreme hardness of this mass-tinted mineral sole allows very high resistance to wear, friction, punctures, as well as abrasion

Classified "large passage" in accordance with the DTU standard, this "ready-to-use" formulation (composed of calibrated quartz, specific hydraulic binders, anti-crack polypropylene fibers, water reducer, plasticizer, plasticizer, pigment oxides and dyes. different adjuvants ....), packaged in 25 kg bag, available in 12 colors that can be mixed with each other, in order to obtain personalized creative shades

Thanks to the multiple creative and decorative possibilities of concrete wax, the freedom of color design, surface aspects, layouts, it allows each work to be distinguished, like a work of art!

The existing support must be clean and sound, otherwise prepare your support as it should, in the context of a support liquid "anhydrite" screed, tiles, terrazzo, marble, lightweight concrete, leveling, wood. .., it is necessary to sand and sweep before applying the epoxy-based "Bestresin" primer on the floor.

In the context of a concrete slab, degrease and clean with a solution of water and acid diluted to 10% followed by an excess rinsing

Protect your walls from any projections of product by a peripheral covering of a polyane film at a reasonable height

Place perimeter joints along your walls and door sills to avoid problems due to the expansion of the concrete, these strips of foam or polystyrene with a thickness of 3 millimeters will remain in place and can be easily cut to size. final level of paving

Before pouring, you can lay out your site using exotic wood, aluminum strip, tiling, bricks, facing stones etc ..., the personalization of your floor will only be enhanced!

Whatever color you choose, the grout gives your waxed concrete floor a unique finish with material and depth effects as well as a moiré and nuance effect due to the natural mineral structure of smooth quartz ( manual or mechanical), this technique can be implemented on a concrete slab, mortar screed, tiling, marble, re-creation or "anhydrite" liquid screed for underfloor heating, by using the appropriate bonding primer to the support, the work s 'heating off and floor at room temperature

The colored quartz paving brings great strength and hardness to the support in order to withstand the most intense traffic (large passages)

Simple and fast, this colored paving allows not to paralyze access during installation

A finishing wax with "Bestcire" polymer emulsion is applied to the paving in order to waterproof, fix and patina the colors, also allowing durability and ease of maintenance

The aging of wax concrete due to the ravages of time, gives it an incomparable patina comparable to a natural material

These coatings fall within the scope of standard P 18 - 305, as such, they meet the dosage conditions by binder and equivalent load, in accordance with their environmental class

Preparation and protection of the site with peripheral fractionation joints (plinths and door sills) of 4 mm

Pouring of a plasticized, fluidized 350 mortar screed 65 mm thick

Sprinkle the ready-to-use "Quartzcoulis" colored mineral grout vertically and as it progresses on the fresh slab

Wait a few hours (depending on climate) for the concrete + grout to set and lift

If necessary, debunk the micro air pockets contained in the grout using a tip

Surface by carefully shoeing (very deep smoothing) the mineral (leather-like) using a manual steel or helicopter trowel (depending on the surface), in order to obtain a glazed finish

Deglaze and polish (a few days later) the residual glaze (carbonation) on the surface using a sander (fine grain of 120 or 140), in order to reveal the effect of material and depth of the mineral

Sweep, then spread 2 coats of "Bestcire" polymer emulsion wax, letting it penetrate for a few hours between each pass

Polish with a polisher or a dry cloth to reveal the patina

The implementation of waxed concrete is a simple technique, carried out with ready-to-use products allowing to renovate while decorating and protecting all new or old supports (including heated floors and tiling), within reach from any professional of your choice, to whom we will be happy to communicate all the installation specifications (anti-crack fibers, resistance to heavy traffic, anti-wear and anti-dust)